Валюта: Р $

Корзина: пусто

ОБЩАЯ СУММА (с учетом скидки)пусто

Перейти в корзину

TriumF. Test bench for testing CR injectors

Article: no article
В наличии
0 Р
  • Overview
  • Set of delivery
  • Technical data
  • Scheme


TRIUMF benches are manufactured with the possibility of retrofitting with a hardware and software complex for encoding Bosch, Delphi, Denso injectors. To encode the Delphi injectors, a device is additionally installed, which allows to create a vacuum in the backleak line of the injector. The set of the vacuum creating device is a gear pump, a venturi tube and an electric motor. The device is installed on the bulkhead, which is located in the lower part of the bench above the cooling unit.

As a working fluid in the test bench, a test liquid of ISO 4113 standard is used. The source of high pressure is a high-pressure fuel pump (HP pump), which has a drive from an asynchronous motor of 4 kW, 1500 rpm. As a feed pump, a gear pump is used, integrated into the injection pump housing and having the same drive.

The vacuum creating device is mounted on a separate gear pump, which is located at the bottom of the bench above the cooler.

For thermostabilization of the test liquid in the tank, the following applies:

  • two radiators with forced air cooling for the backleak line from the injection pump and the -backleak line from the pressure accumulator (rail).
  • independent cooler with air heat exchanger.
  • 1000 W tubular electric heater

Working pressure up to 1800 bar. It is possible to increase the working pressure to 2400 bar.

The bench has an electronic measuring system with the possibility of simultaneous testing of 4 injectors.

The program with test plans is included in the set of delivery. Software updates, including new test plans, are published twice a year and are provided free of charge.

Set of delivery

*PC with monitor and keyboard1
Injector holder Ø 9 mm2
Cable for connecting pressure regulator1
Cable for connecting pressure sensor1
Universal cable for injectors1
Cable for Delphi injectors type 11
Cable for Delphi injectors type 21
Cable for Bosch injectors type 11
Cable for Bosch injectors type 21
Cable for truck injectors type 11
Cable for truck injectors type 21
High pressure line М14хМ14х400 mm4
DL-UNI50083 Adapter М14хМ12 mm4
Set of adapters for injector backleak1
Set of connectors of Denso injector backleak1
Doorlock key4

* installed on the bench

** optional

Technical data

Rotation speed1500 min-1
Main engine power4 kW
Number of simultaneously tested injectors4
Tank capacity30 dm3
Supply voltage3x400V/230V~ 50 Hz
Valve supply for electronic measurement system of injectors24 V
Pulsing frequency of the injectors opening60 – 1500 min-1
Pulsing duration of the injectors opening100 – 3000 mcs
Test fluid pressure setting of the test liquid in a range0-100±1 degr.С
Test fluid overflow temperature controlon each injector
Electronic pressure measurement in Rail in a range0 – 1800±5bar
Rail pressure setting in range0 – 1800±5bar
**system pressure change in the range0 – 2400±5bar
Number of measuring sensors2
Measuring speed of the measuring unit0,01 l/min-0,5 l/min
Accuracy of measurement (cars)no more than 1%
Accuracy of measurement (truck cars) 0,15 mm3 — 400 mm3no more than 1,5%
Resolution of injector measuring unit~ 0,1 mm3 /1 cycle (injection)
Cooler compressor capacity800 Wt
Maximum current23 A
Test liquid heater power1000 W
Safety screenpolycarbonate 10 mm
DimentionsW 1010, H 1504, D 660
Total weight430 kg


Дорогие друзья!

К сожалению, Ваш браузер не поддерживает современные технологии используемые на нашем сайте.

Пожалуйста, обновите браузер, скачав его по ссылкам ниже, или обратитесь к системному администратору, обслуживающему Ваш компьютер.

Internet Explorer







Opera Software